Daily maintenance procedures of Qingdao swing gate manufacturer

箱擦干净，砂光表面应该沿长纹路擦(维护厚纹路方向)否则会影响机箱外观，镜光

If the case is cleaned, the sanded surface should be rubbed along long lines (maintaining the direction of thick lines) or it will affect the appearance of the case and the mirror light.

表面用抛光轮和抛光腊打磨，有条件的外表可以涂上些防锈油。喷涂、喷漆的机箱，用软布将灰尘擦掉，外表有划伤的可用相同颜色的油漆补一下，千万记住不要将对射

The surface is polished with polishing wheel and polishing wax, and some antirust oil can be applied on the surface if conditions permit. Spraying, painting of the chassis, with soft cloth to wipe away the dust, the appearance of scratches can be repaired with the same color of paint, do not remember to shoot

电眼的中央涂了油漆，一旦上面有了被掩盖，摆闸和翼闸将会误报警，构成不用要的省事。

The central part of the electric eye is painted. Once the upper part is covered up, the swing and wing brakes will alarm by mistake, which makes it unnecessary to save time.

二．摆闸厂家机芯的颐养 颐养前摆闸应切断电源，翻开机盖，首先清洁表面灰尘，将传动部分喷上黄油，摆闸需将取下电机，将黄油涂到齿轮和轮槽上面，

2. The swing brake manufacturer should cut off the power supply, open the cover, clean the surface dust first, spray the transmission part with butter, remove the motor and apply butter to the gears and grooves before the swing brake manufacturer can take care of itself.

按原位置将电机固定，检查联接件螺杆能否有松动，拧紧，限位开关和限位金属片不要随意调，间隙1-2mm太远感应不到，也太近容易损坏。

Fix the motor in place, check whether the connecting screw is loose and tightened, limit switch and limit metal sheet should not be adjusted at will, the gap of 1-2mm is too far to be sensed, and it is too near to be damaged.

三．摆闸电源部分维护 摆闸切断电源，去掉表面灰尘，检查各插件能否有松动，插好，拧紧，不要随意改换接线位置，外接电源能否有外露，

3. The swing power supply part maintains swing off power supply, removes surface dust, checks whether each plug-in can be loosened, plugged in, tightened, and does not change wiring position at will, whether the external power supply can be exposed.

有外露情况应及时包扎好，能否有漏电情况，及时处置，参照说明书，检查各端接口的技术参数能否正常，对老化的电子元器件及时改换。

When exposed, it should be wrapped up in time, whether there is leakage or not, disposed of in time. Refer to the instruction, check whether the technical parameters of each end interface are normal, and change the aging electronic components in time.

摆闸和翼闸维护颐养一定要有专业人员去维护，机芯和电控部分，先要切断电源，安全操作，须经过专业培训的人员，对强电和弱点充分了解，方可上岗操作。

Swing and wing brake maintenance must have professional personnel to maintain, the machine core and electrical control part, first cut off the power supply, safe operation, must be trained professionals, fully understand the strong electricity and weaknesses, can be on duty operation.